Cabinet geometry, weight, and power for the Sony 1.2mm, plus a calculator that turns a target wall size into cabinet counts, resolution, weight, and circuit loading.
Estimated specs. Premium fixed install / studio preset. Verify against the manufacturer cut sheet before ordering.
Pixel pitch 1.26 mm, 129,600 pixels per cabinet at 480 by 270
Cabinet 608 by 342 mm (1.99 by 1.12 ft)
10 kg (22 lb) per cabinet, about 48.1 kg per square metre
170 W peak per cabinet, 60 W average, about 818 W per square metre at peak
11 cabinets per 20A 120V circuit, 17 per 16A 230V circuit, at peak draw
The Sony 1.2mm is indoor 1.26 mm pitch LED with a 608 by 342 mm cabinet carrying 480 by 270 pixels. Each cabinet weighs 10 kg (22 lb) and draws up to 170 W.
Those four numbers drive everything else on a build: how many cabinets reach your target size, what the wall weighs on the rigging, how many circuits the distro needs, and what resolution the processor has to feed.
Pixel pitch: 1.26 mm
Cabinet resolution: 480 by 270 (129,600 pixels)
Cabinet size: 608 by 342 mm
Brightness: 1000 nits
Refresh rate: 3840 Hz
Typical processor platform: Other
Power and circuits for the 1.2mm
At the 170 W peak figure, one 20A 120V circuit carries 11 cabinets and one 16A 230V circuit carries 17. Both numbers apply the 80 percent continuous load derate (NEC 210.20, IEC 60364), which is the same maths WireFlow uses when it sizes a real wall.
Size the distro on peak, not average. Average draw of 60 W tells you what the wall costs to run over a show; peak is what trips a breaker during a white flash.
Peak per cabinet: 170 W
Average per cabinet: 60 W
Cabinets per 20A 120V circuit: 11
Cabinets per 16A 230V circuit: 17
Input voltage: 100 to 240 V at 50/60 Hz
Worked example: a 4 by 3 wall
12 Sony 1.2mm cabinets in a 4 wide by 3 high grid make a wall 2.43 by 1.03 m (7.98 by 3.37 ft) at 1920 by 810 pixels.
That wall weighs about 120 kg before rigging hardware and draws up to 2,040 W, which needs 2 circuits at 20A 120V or 1 at 16A 230V.
Wall size: 2.43 by 1.03 m
Resolution: 1920 by 810 pixels
Weight: about 120 kg
Peak draw: 2,040 W
Circuits: 2 at 20A 120V, 1 at 16A 230V
Build this wall in WireFlow
The calculator above sizes a wall to your target dimensions with this panel's real cabinet geometry, then reports cabinet count, resolution, weight, and circuits. From there WireFlow can drop the finished wall straight into a diagram, already wired to its processors, and the cable schedule and power report update with it.
Free to start: three editable diagrams, no credit card. Pro is $5/month at founder pricing.
Frequently asked questions
What is the pixel pitch of the Sony 1.2mm?
1.26 mm. Each 608 by 342 mm cabinet carries 480 by 270 pixels, or 129,600 in total.
How much power does the Sony 1.2mm draw?
Up to 170 W per cabinet at peak, averaging around 60 W in normal content. That works out to roughly 818 W per square metre at peak. Size distro on the peak figure.
How many 1.2mm cabinets fit on one circuit?
11 on a 20A 120V circuit and 17 on a 16A 230V circuit, both at peak draw with the standard 80 percent continuous load derate applied.
How much does the Sony 1.2mm weigh?
10 kg (22 lb) per cabinet, which is about 48.1 kg per square metre of wall. A 4 by 3 wall of them comes to roughly 120 kg before rigging hardware.
Are these Sony specs exact?
Estimated specs. Premium fixed install / studio preset. Verify against the manufacturer cut sheet before ordering.
Can I design a wall with this panel in WireFlow?
Yes. Pick this panel, give it a target size, and WireFlow works out the cabinet grid, pixel map, weight, and power per circuit, then places the wall into your diagram already wired to its processors. Free to start with three diagrams and no card.