ROE Visual V8: 8.9 mm pitch, 1000 by 1000 mm cabinet.
Cabinet geometry, weight, and power for the ROE Visual V8, plus a calculator that turns a target wall size into cabinet counts, resolution, weight, and circuit loading.
Estimated specs. Transparent outdoor/event preset. Verify exact Vanish variant. Verify against the manufacturer cut sheet before ordering.
Pixel pitch 8.9 mm, 12,544 pixels per cabinet at 112 by 112
Cabinet 1000 by 1000 mm (3.28 by 3.28 ft), 80 mm deep
13 kg (28.7 lb) per cabinet, about 13 kg per square metre
400 W peak per cabinet, 200 W average, about 400 W per square metre at peak
4 cabinets per 20A 120V circuit, 7 per 16A 230V circuit, at peak draw
The ROE Visual V8 is outdoor 8.9 mm pitch LED with a 1000 by 1000 mm cabinet carrying 112 by 112 pixels. Each cabinet weighs 13 kg (28.7 lb) and draws up to 400 W.
Those four numbers drive everything else on a build: how many cabinets reach your target size, what the wall weighs on the rigging, how many circuits the distro needs, and what resolution the processor has to feed.
Pixel pitch: 8.9 mm
Cabinet resolution: 112 by 112 (12,544 pixels)
Cabinet size: 1000 by 1000 mm
Brightness: 4500 nits
Refresh rate: 3840 Hz
IP rating: IP65
Typical processor platform: Brompton
Power and circuits for the V8
At the 400 W peak figure, one 20A 120V circuit carries 4 cabinets and one 16A 230V circuit carries 7. Both numbers apply the 80 percent continuous load derate (NEC 210.20, IEC 60364), which is the same maths WireFlow uses when it sizes a real wall.
Size the distro on peak, not average. Average draw of 200 W tells you what the wall costs to run over a show; peak is what trips a breaker during a white flash.
Peak per cabinet: 400 W
Average per cabinet: 200 W
Cabinets per 20A 120V circuit: 4
Cabinets per 16A 230V circuit: 7
Input voltage: 100 to 240 V at 50/60 Hz
Worked example: a 4 by 3 wall
12 ROE Visual V8 cabinets in a 4 wide by 3 high grid make a wall 4 by 3 m (13.12 by 9.84 ft) at 448 by 336 pixels.
That wall weighs about 156 kg before rigging hardware and draws up to 4,800 W, which needs 3 circuits at 20A 120V or 2 at 16A 230V.
Wall size: 4 by 3 m
Resolution: 448 by 336 pixels
Weight: about 156 kg
Peak draw: 4,800 W
Circuits: 3 at 20A 120V, 2 at 16A 230V
Build this wall in WireFlow
The calculator above sizes a wall to your target dimensions with this panel's real cabinet geometry, then reports cabinet count, resolution, weight, and circuits. From there WireFlow can drop the finished wall straight into a diagram, already wired to its processors, and the cable schedule and power report update with it.
Free to start: three editable diagrams, no credit card. Pro is $5/month at founder pricing.
Frequently asked questions
What is the pixel pitch of the ROE Visual V8?
8.9 mm. Each 1000 by 1000 mm cabinet carries 112 by 112 pixels, or 12,544 in total.
How much power does the ROE Visual V8 draw?
Up to 400 W per cabinet at peak, averaging around 200 W in normal content. That works out to roughly 400 W per square metre at peak. Size distro on the peak figure.
How many V8 cabinets fit on one circuit?
4 on a 20A 120V circuit and 7 on a 16A 230V circuit, both at peak draw with the standard 80 percent continuous load derate applied.
How much does the ROE Visual V8 weigh?
13 kg (28.7 lb) per cabinet, which is about 13 kg per square metre of wall. A 4 by 3 wall of them comes to roughly 156 kg before rigging hardware.
Are these ROE Visual specs exact?
Estimated specs. Transparent outdoor/event preset. Verify exact Vanish variant. Verify against the manufacturer cut sheet before ordering.
Can I design a wall with this panel in WireFlow?
Yes. Pick this panel, give it a target size, and WireFlow works out the cabinet grid, pixel map, weight, and power per circuit, then places the wall into your diagram already wired to its processors. Free to start with three diagrams and no card.