ROE Visual RB2.3: 2.31 mm pitch, 500 by 500 mm cabinet.
Cabinet geometry, weight, and power for the ROE Visual RB2.3, plus a calculator that turns a target wall size into cabinet counts, resolution, weight, and circuit loading.
Estimated specs. Fine-pitch XR/broadcast preset. Verify exact Ruby variant. Verify against the manufacturer cut sheet before ordering.
Pixel pitch 2.31 mm, 46,656 pixels per cabinet at 216 by 216
Cabinet 500 by 500 mm (1.64 by 1.64 ft), 80 mm deep
9.5 kg (20.9 lb) per cabinet, about 38 kg per square metre
170 W peak per cabinet, 85 W average, about 680 W per square metre at peak
11 cabinets per 20A 120V circuit, 17 per 16A 230V circuit, at peak draw
The ROE Visual RB2.3 is indoor 2.31 mm pitch LED with a 500 by 500 mm cabinet carrying 216 by 216 pixels. Each cabinet weighs 9.5 kg (20.9 lb) and draws up to 170 W.
Those four numbers drive everything else on a build: how many cabinets reach your target size, what the wall weighs on the rigging, how many circuits the distro needs, and what resolution the processor has to feed.
Pixel pitch: 2.31 mm
Cabinet resolution: 216 by 216 (46,656 pixels)
Cabinet size: 500 by 500 mm
Brightness: 1500 nits
Refresh rate: 7680 Hz
Typical processor platform: Brompton
Power and circuits for the RB2.3
At the 170 W peak figure, one 20A 120V circuit carries 11 cabinets and one 16A 230V circuit carries 17. Both numbers apply the 80 percent continuous load derate (NEC 210.20, IEC 60364), which is the same maths WireFlow uses when it sizes a real wall.
Size the distro on peak, not average. Average draw of 85 W tells you what the wall costs to run over a show; peak is what trips a breaker during a white flash.
Peak per cabinet: 170 W
Average per cabinet: 85 W
Cabinets per 20A 120V circuit: 11
Cabinets per 16A 230V circuit: 17
Input voltage: 100 to 240 V at 50/60 Hz
Worked example: a 4 by 3 wall
12 ROE Visual RB2.3 cabinets in a 4 wide by 3 high grid make a wall 2 by 1.5 m (6.56 by 4.92 ft) at 864 by 648 pixels.
That wall weighs about 114 kg before rigging hardware and draws up to 2,040 W, which needs 2 circuits at 20A 120V or 1 at 16A 230V.
Wall size: 2 by 1.5 m
Resolution: 864 by 648 pixels
Weight: about 114 kg
Peak draw: 2,040 W
Circuits: 2 at 20A 120V, 1 at 16A 230V
Build this wall in WireFlow
The calculator above sizes a wall to your target dimensions with this panel's real cabinet geometry, then reports cabinet count, resolution, weight, and circuits. From there WireFlow can drop the finished wall straight into a diagram, already wired to its processors, and the cable schedule and power report update with it.
Free to start: three editable diagrams, no credit card. Pro is $5/month at founder pricing.
Frequently asked questions
What is the pixel pitch of the ROE Visual RB2.3?
2.31 mm. Each 500 by 500 mm cabinet carries 216 by 216 pixels, or 46,656 in total.
How much power does the ROE Visual RB2.3 draw?
Up to 170 W per cabinet at peak, averaging around 85 W in normal content. That works out to roughly 680 W per square metre at peak. Size distro on the peak figure.
How many RB2.3 cabinets fit on one circuit?
11 on a 20A 120V circuit and 17 on a 16A 230V circuit, both at peak draw with the standard 80 percent continuous load derate applied.
How much does the ROE Visual RB2.3 weigh?
9.5 kg (20.9 lb) per cabinet, which is about 38 kg per square metre of wall. A 4 by 3 wall of them comes to roughly 114 kg before rigging hardware.
Are these ROE Visual specs exact?
Estimated specs. Fine-pitch XR/broadcast preset. Verify exact Ruby variant. Verify against the manufacturer cut sheet before ordering.
Can I design a wall with this panel in WireFlow?
Yes. Pick this panel, give it a target size, and WireFlow works out the cabinet grid, pixel map, weight, and power per circuit, then places the wall into your diagram already wired to its processors. Free to start with three diagrams and no card.