ROE Visual CB8: 8.33 mm pitch, 600 by 1200 mm cabinet.
Cabinet geometry, weight, and power for the ROE Visual CB8, plus a calculator that turns a target wall size into cabinet counts, resolution, weight, and circuit loading.
Estimated specs. Large outdoor/touring fallback. Verify exact Carbon variant. Verify against the manufacturer cut sheet before ordering.
Pixel pitch 8.33 mm, 10,368 pixels per cabinet at 72 by 144
Cabinet 600 by 1200 mm (1.97 by 3.94 ft), 77 mm deep
14 kg (30.9 lb) per cabinet, about 19.4 kg per square metre
500 W peak per cabinet, 250 W average, about 694 W per square metre at peak
3 cabinets per 20A 120V circuit, 5 per 16A 230V circuit, at peak draw
The ROE Visual CB8 is outdoor 8.33 mm pitch LED with a 600 by 1200 mm cabinet carrying 72 by 144 pixels. Each cabinet weighs 14 kg (30.9 lb) and draws up to 500 W.
Those four numbers drive everything else on a build: how many cabinets reach your target size, what the wall weighs on the rigging, how many circuits the distro needs, and what resolution the processor has to feed.
Pixel pitch: 8.33 mm
Cabinet resolution: 72 by 144 (10,368 pixels)
Cabinet size: 600 by 1200 mm
Brightness: 6000 nits
Refresh rate: 3840 Hz
IP rating: IP65
Typical processor platform: Brompton
Power and circuits for the CB8
At the 500 W peak figure, one 20A 120V circuit carries 3 cabinets and one 16A 230V circuit carries 5. Both numbers apply the 80 percent continuous load derate (NEC 210.20, IEC 60364), which is the same maths WireFlow uses when it sizes a real wall.
Size the distro on peak, not average. Average draw of 250 W tells you what the wall costs to run over a show; peak is what trips a breaker during a white flash.
Peak per cabinet: 500 W
Average per cabinet: 250 W
Cabinets per 20A 120V circuit: 3
Cabinets per 16A 230V circuit: 5
Input voltage: 100 to 240 V at 50/60 Hz
Worked example: a 4 by 3 wall
12 ROE Visual CB8 cabinets in a 4 wide by 3 high grid make a wall 2.4 by 3.6 m (7.87 by 11.81 ft) at 288 by 432 pixels.
That wall weighs about 168 kg before rigging hardware and draws up to 6,000 W, which needs 4 circuits at 20A 120V or 3 at 16A 230V.
Wall size: 2.4 by 3.6 m
Resolution: 288 by 432 pixels
Weight: about 168 kg
Peak draw: 6,000 W
Circuits: 4 at 20A 120V, 3 at 16A 230V
Build this wall in WireFlow
The calculator above sizes a wall to your target dimensions with this panel's real cabinet geometry, then reports cabinet count, resolution, weight, and circuits. From there WireFlow can drop the finished wall straight into a diagram, already wired to its processors, and the cable schedule and power report update with it.
Free to start: three editable diagrams, no credit card. Pro is $5/month at founder pricing.
Frequently asked questions
What is the pixel pitch of the ROE Visual CB8?
8.33 mm. Each 600 by 1200 mm cabinet carries 72 by 144 pixels, or 10,368 in total.
How much power does the ROE Visual CB8 draw?
Up to 500 W per cabinet at peak, averaging around 250 W in normal content. That works out to roughly 694 W per square metre at peak. Size distro on the peak figure.
How many CB8 cabinets fit on one circuit?
3 on a 20A 120V circuit and 5 on a 16A 230V circuit, both at peak draw with the standard 80 percent continuous load derate applied.
How much does the ROE Visual CB8 weigh?
14 kg (30.9 lb) per cabinet, which is about 19.4 kg per square metre of wall. A 4 by 3 wall of them comes to roughly 168 kg before rigging hardware.
Are these ROE Visual specs exact?
Estimated specs. Large outdoor/touring fallback. Verify exact Carbon variant. Verify against the manufacturer cut sheet before ordering.
Can I design a wall with this panel in WireFlow?
Yes. Pick this panel, give it a target size, and WireFlow works out the cabinet grid, pixel map, weight, and power per circuit, then places the wall into your diagram already wired to its processors. Free to start with three diagrams and no card.