Chauvet Professional F2: 2.9 mm pitch, 500 by 1000 mm cabinet.
Cabinet geometry, weight, and power for the Chauvet Professional F2, plus a calculator that turns a target wall size into cabinet counts, resolution, weight, and circuit loading.
Vendor supplied specs. Corporate/event F-series preset. Verify exact panel vs bundle listing. Verify against the manufacturer cut sheet before ordering.
Pixel pitch 2.9 mm, 56,448 pixels per cabinet at 168 by 336
Cabinet 500 by 1000 mm (1.64 by 3.28 ft), 77 mm deep
13.6 kg (30 lb) per cabinet, about 27.2 kg per square metre
333 W peak per cabinet, 111 W average, about 666 W per square metre at peak
5 cabinets per 20A 120V circuit, 8 per 16A 230V circuit, at peak draw
The Chauvet Professional F2 is indoor 2.9 mm pitch LED with a 500 by 1000 mm cabinet carrying 168 by 336 pixels. Each cabinet weighs 13.6 kg (30 lb) and draws up to 333 W.
Those four numbers drive everything else on a build: how many cabinets reach your target size, what the wall weighs on the rigging, how many circuits the distro needs, and what resolution the processor has to feed.
Pixel pitch: 2.9 mm
Cabinet resolution: 168 by 336 (56,448 pixels)
Cabinet size: 500 by 1000 mm
Brightness: 1500 nits
Refresh rate: 3840 Hz
Typical processor platform: Novastar
Power and circuits for the F2
At the 333 W peak figure, one 20A 120V circuit carries 5 cabinets and one 16A 230V circuit carries 8. Both numbers apply the 80 percent continuous load derate (NEC 210.20, IEC 60364), which is the same maths WireFlow uses when it sizes a real wall.
Size the distro on peak, not average. Average draw of 111 W tells you what the wall costs to run over a show; peak is what trips a breaker during a white flash.
Peak per cabinet: 333 W
Average per cabinet: 111 W
Cabinets per 20A 120V circuit: 5
Cabinets per 16A 230V circuit: 8
Input voltage: 100 to 240 V at 50/60 Hz
Worked example: a 4 by 3 wall
12 Chauvet Professional F2 cabinets in a 4 wide by 3 high grid make a wall 2 by 3 m (6.56 by 9.84 ft) at 672 by 1008 pixels.
That wall weighs about 163.2 kg before rigging hardware and draws up to 3,996 W, which needs 3 circuits at 20A 120V or 2 at 16A 230V.
Wall size: 2 by 3 m
Resolution: 672 by 1008 pixels
Weight: about 163.2 kg
Peak draw: 3,996 W
Circuits: 3 at 20A 120V, 2 at 16A 230V
Build this wall in WireFlow
The calculator above sizes a wall to your target dimensions with this panel's real cabinet geometry, then reports cabinet count, resolution, weight, and circuits. From there WireFlow can drop the finished wall straight into a diagram, already wired to its processors, and the cable schedule and power report update with it.
Free to start: three editable diagrams, no credit card. Pro is $5/month at founder pricing.
Frequently asked questions
What is the pixel pitch of the Chauvet Professional F2?
2.9 mm. Each 500 by 1000 mm cabinet carries 168 by 336 pixels, or 56,448 in total.
How much power does the Chauvet Professional F2 draw?
Up to 333 W per cabinet at peak, averaging around 111 W in normal content. That works out to roughly 666 W per square metre at peak. Size distro on the peak figure.
How many F2 cabinets fit on one circuit?
5 on a 20A 120V circuit and 8 on a 16A 230V circuit, both at peak draw with the standard 80 percent continuous load derate applied.
How much does the Chauvet Professional F2 weigh?
13.6 kg (30 lb) per cabinet, which is about 27.2 kg per square metre of wall. A 4 by 3 wall of them comes to roughly 163.2 kg before rigging hardware.
Are these Chauvet Professional specs exact?
Vendor supplied specs. Corporate/event F-series preset. Verify exact panel vs bundle listing. Verify against the manufacturer cut sheet before ordering.
Can I design a wall with this panel in WireFlow?
Yes. Pick this panel, give it a target size, and WireFlow works out the cabinet grid, pixel map, weight, and power per circuit, then places the wall into your diagram already wired to its processors. Free to start with three diagrams and no card.